Linux version 2.6.19 (root@Knoppix) (gcc version 4.1.2 20061028 (prerelease) (Debian 4.1.1-19)) #7 SMP PREEMPT Sun Dec 17 22:01:07 CET 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 0000000000091000 (usable) BIOS-e820: 0000000000091000 - 0000000000098000 (reserved) BIOS-e820: 00000000000e6800 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000007ef0000 (usable) BIOS-e820: 0000000007ef0000 - 0000000007eff000 (ACPI data) BIOS-e820: 0000000007eff000 - 0000000007f00000 (ACPI NVS) BIOS-e820: 0000000007f00000 - 0000000008000000 (reserved) BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) user-defined physical RAM map: user: 0000000000000000 - 0000000000091000 (usable) user: 0000000000091000 - 0000000000098000 (reserved) user: 00000000000e6800 - 0000000000100000 (reserved) user: 0000000000100000 - 0000000007e00000 (usable) 0MB HIGHMEM available. 126MB LOWMEM available. Entering add_active_range(0, 0, 32256) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 32256 HighMem 32256 -> 32256 early_node_map[1] active PFN ranges 0: 0 -> 32256 On node 0 totalpages: 32256 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 220 pages used for memmap Normal zone: 27940 pages, LIFO batch:7 HighMem zone: 0 pages used for memmap DMI 2.3 present. ACPI: RSDP (v000 PTLTD ) @ 0x000f6ef0 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x07efc901 ACPI: FADT (v001 INTEL Whitney 0x06040000 PTL 0x000f4240) @ 0x07efef8c ACPI: DSDT (v001 INTEL Whitney 0x06040000 MSFT 0x0100000b) @ 0x00000000 ACPI: PM-Timer IO Port: 0x1008 Allocating PCI resources starting at 10000000 (gap: 07e00000:f8200000) Detected 564.839 MHz processor. Built 1 zonelists. Total pages: 32004 Kernel command line: ramdisk_size=100000 init=/etc/init lang=da apm=power-off nomce loglevel=0 BOOT_IMAGE=knoppix vga=normal mem=126M noudev 2 Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (0110a000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 121676k/129024k available (2747k kernel code, 6740k reserved, 958k data, 336k init, 0k highmem) virtual kernel memory layout: fixmap : 0xffe16000 - 0xfffff000 (1956 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xc8800000 - 0xff7fe000 ( 879 MB) lowmem : 0xc0000000 - 0xc7e00000 ( 126 MB) .init : 0xc04a6000 - 0xc04fa000 ( 336 kB) .data : 0xc03aef9c - 0xc049e7b4 ( 958 kB) .text : 0xc0100000 - 0xc03aef9c (2747 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 1130.97 BogoMIPS (lpj=2261947) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 128K CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. Checking for popad bug... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 16k freed ACPI: Core revision 20060707 ACPI: setting ELCR to 0200 (from 0220) CPU0: Intel Celeron (Coppermine) stepping 0a SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Brought up 1 CPUs checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 1188k freed NET: Registered protocol family 16 EISA bus registered ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd9cf, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:00:01.0 PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 1180-11bf claimed by ICH4 GPIO PCI: Transparent bridge - 0000:00:1e.0 PCI: Bus #02 (-#05) is hidden behind transparent bridge #01 (-#01) (try 'pci=assign-busses') Please report the result to linux-kernel to fix this permanently ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs *5 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 5 15) *9 ACPI: PCI Interrupt Link [LNKC] (IRQs 5 15) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 5 15) *9 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 15 devices PnPBIOS: Disabled by ACPI PNP intel_rng: FWH not detected SCSI subsystem initialized libata version 2.00 loaded. PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default PCI: Ignore bogus resource 6 [0:0] of 0000:00:01.0 PCI: Bus 2, cardbus bridge: 0000:01:01.0 IO window: 00003400-000034ff IO window: 00003800-000038ff PREFETCH window: 10000000-11ffffff MEM window: 12000000-13ffffff PCI: Bridge: 0000:00:1e.0 IO window: 3000-3fff MEM window: f4100000-f41fffff PREFETCH window: 10000000-11ffffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:01:01.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:01:01.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 49152 bytes) TCP bind hash table entries: 2048 (order: 2, 24576 bytes) TCP: Hash tables configured (established 4096 bind 2048) TCP reno registered audit: initializing netlink socket (disabled) audit(1224973997.692:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) fuse init (API version 7.8) fuse distribution version: 2.6.1 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered (default) io scheduler cfq registered isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0000 -> 0001) ICH: chipset revision 2 ICH: not 100% native mode: will probe irqs later ICH: neither IDE port enabled (BIOS) Probing IDE interface ide0... Probing IDE interface ide1... Loading iSCSI transport class v2.0-724.<6>PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice EISA: Probing bus 0 at eisa.0 Cannot allocate resource for EISA slot 1 Cannot allocate resource for EISA slot 3 EISA: Detected 0 cards. Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 15 Using IPI No-Shortcut mode ACPI: (supports S0 S1 S5) Time: tsc clocksource has been installed. input: AT Translated Set 2 keyboard as /class/input/input0 RAMDISK: Compressed image found at block 0 EXT2-fs warning: checktime reached, running e2fsck is recommended VFS: Mounted root (ext2 filesystem). Failed initialization of WD-7000 SCSI card! usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5 ACPI: PCI Interrupt 0000:00:1f.2[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1f.2 to 64 uhci_hcd 0000:00:1f.2: UHCI Host Controller uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1f.2: irq 5, io base 0x00001820 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) usb 1-2: new full speed USB device using uhci_hcd and address 2 usb 1-2: configuration #1 chosen from 1 choice usbcore: registered new interface driver libusual usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new interface driver usb-storage USB Mass Storage support registered. ieee1394: Initialized config rom entry `ip1394' ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) ieee1394: sbp2: Try serialize_io=0 for better performance scsi 0:0:0:0: Direct-Access SanDisk SD Plus 0.1 PQ: 0 ANSI: 2 SCSI device sda: 3970048 512-byte hdwr sectors (2033 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 00 sda: assuming drive cache: write through SCSI device sda: 3970048 512-byte hdwr sectors (2033 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 00 sda: assuming drive cache: write through sda: sda1 sd 0:0:0:0: Attached scsi removable disk sda usb-storage: device scan complete Unable to identify CD-ROM format. VFS: Can't find an ext2 filesystem on dev sda. ReiserFS: sda: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on sda FAT: bogus number of reserved sectors VFS: Can't find a valid FAT filesystem on dev sda. Unable to identify CD-ROM format. VFS: Can't find an ext2 filesystem on dev sda1. ReiserFS: sda1: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on sda1 cloop: Initializing cloop v2.05 cloop: loaded (max 8 devices) cloop: /cdrom/KNOPPIX/KNOPPIX: 15609 blocks, 131072 bytes/block, largest block is 131098 bytes. ISO 9660 Extensions: RRIP_1991A aufs 2.6.19-20061211 Freeing unused kernel memory: 336k freed ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] Using specific hotkey driver ACPI: Invalid PBLK length [5] cpufreq: No nForce2 chipset. powernow: This module only works with AMD K7 CPUs Yenta: CardBus bridge found at 0000:01:01.0 [0000:0000] Yenta: Enabling burst memory read transactions Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:01:01.0, mfunc 0x01001002, devctl 0x46 Yenta: ISA IRQ mask 0x0098, PCI irq 5 Socket status: 30000006 Yenta: Raising subordinate bus# of parent bus (#01) from #01 to #05 pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff cs: IO port probe 0x3000-0x3fff: clean. pcmcia: parent PCI bridge Memory window: 0xf4100000 - 0xf41fffff pcmcia: parent PCI bridge Memory window: 0x10000000 - 0x11ffffff pcmcia: Detected deprecated PCMCIA ioctl usage from process: cardmgr. pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools. pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details. cs: IO port probe 0xc00-0xcff: clean. cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0x800-0x80f: clean. cs: IO port probe 0x100-0x4ff: excluding 0x200-0x207 0x290-0x297 0x2e0-0x2ef 0x2f8-0x2ff 0x378-0x37f 0x3e8-0x3ff 0x4d0-0x4d7 cs: IO port probe 0xa00-0xaff: clean. Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A serial8250: ttyS3 at I/O 0x2e8 (irq = 3) is a 16550A sd 0:0:0:0: Attached scsi generic sg0 type 0 ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel i810 Chipset. agpgart: AGP aperture is 64M @ 0xf8000000 8139too Fast Ethernet driver 0.9.28 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5 ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5 eth0: RealTek RTL8139 at 0xc8a70000, 00:40:b3:04:20:85, IRQ 5 eth0: Identified 8139 chip type 'RTL-8139C' Intel 810 + AC97 Audio, version 1.01, 23:28:07 Dec 13 2006 ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1f.5 to 64 i810: Intel ICH 82801AA found at IO 0x1300 and 0x1200, MEM 0x0000 and 0x0000, IRQ 5 i810_audio: Audio Controller supports 2 channels. i810_audio: Defaulting to base 2 channel mode. i810_audio: Resetting connection 0 ac97_codec: AC97 Audio codec, id: ADS72 (Analog Devices AD1881A) i810_audio: AC'97 codec 0 Unable to map surround DAC's (or DAC's not present), total channels = 2 device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: dm-devel@redhat.com eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 NET: Registered protocol family 17 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1