ocessor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1201.71 BogoMIPS (lpj=2403424)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 00803035 80803035 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 00803135 80803035 00000000 00000000 00000000 00000000 00000000
mtrr: v2.0 (20020519)
CPU: Centaur VIA Samuel 2 stepping 03
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 12a0)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb2d0, last bus=3
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0400-047f claimed by vt8235 PM
PCI quirk: region 0500-050f claimed by vt8235 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 4 5 6 7 *12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 4 5 6 *7 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 4 *5 6 7 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 4 5 6 7 12) *9
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: 00:01: ioport range 0x400-0x47f could not be reserved
pnp: 00:01: ioport range 0x500-0x50f has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: dc000000-ddffffff
  PREFETCH window: d8000000-dbffffff
PCI: Bus 2, cardbus bridge: 0000:00:0a.0
  IO window: 00001000-000010ff
  IO window: 00001400-000014ff
  PREFETCH window: 40000000-41ffffff
  MEM window: 42000000-43ffffff
PCI: Bus 6, cardbus bridge: 0000:00:0a.1
  IO window: 00001800-000018ff
  IO window: 00001c00-00001cff
  PREFETCH window: 44000000-45ffffff
  MEM window: 46000000-47ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 12 (level, low) -> IRQ 12
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
longhaul: VIA C3 'Samuel 2' [C5B] CPU detected.  Longhaul v1 supported.
audit: initializing netlink socket (disabled)
audit(1137745085.752:1): initialized
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
mice: PS/2 mouse device common for all mice
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 12 (level, low) -> IRQ 12
eth0: VIA Rhine II at 0xde00c000, 00:40:63:d9:d1:6d, IRQ 12.
eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 45e1.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 12 (level, low) -> IRQ 12
PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 12
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard on isa0060/serio0
hda: Maxtor 7L300R0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 1024KiB
hda: 586114704 sectors (300090 MB) w/16384KiB Cache, CHS=36483/255/63, UDMA(133)
hda: cache flushes supported
 hda: hda1 hda2
ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[7]  MMIO=[de00a000-de00a7ff]  Max Packet=[2048]
usbmon: debugfs is not available
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 6
PCI: setting IRQ 6 as level-triggered
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6
PCI: Via IRQ fixup for 0000:00:10.3, from 9 to 6
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: reset hcs_params 0x3206 dbg=0 cc=3 pcc=2 ordered !ppc ports=6
ehci_hcd 0000:00:10.3: reset hcc_params 6872 thresh 7 uframes 256/512/1024
ehci_hcd 0000:00:10.3: capability 0001 at 68
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: irq 6, io mem 0xde00b000
ehci_hcd 0000:00:10.3: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:10.3: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
ehci_hcd 0000:00:10.3: supports USB remote wakeup
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.14-gentoo-r5-patch-vt1211 ehci_hcd
usb usb1: SerialNumber: 0000:00:10.3
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: state 5 ports 6 chg 0000 evt 0000
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: detected 2 ports
uhci_hcd 0000:00:10.0: check_and_reset_hc: legsup = 0x0010
uhci_hcd 0000:00:10.0: Performing full reset
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 12, io base 0x0000b400
uhci_hcd 0000:00:10.0: supports USB remote wakeup
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.14-gentoo-r5-patch-vt1211 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0000
uhci_hcd 0000:00:10.0: port 1 portsc 008a,00
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: detected 2 ports
uhci_hcd 0000:00:10.1: check_and_reset_hc: legsup = 0x0010
uhci_hcd 0000:00:10.1: Performing full reset
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 7, io base 0x0000b800
uhci_hcd 0000:00:10.1: supports USB remote wakeup
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.14-gentoo-r5-patch-vt1211 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: detected 2 ports
uhci_hcd 0000:00:10.2: check_and_reset_hc: legsup = 0x0010
uhci_hcd 0000:00:10.2: Performing full reset
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 5, io base 0x0000bc00
uhci_hcd 0000:00:10.2: supports USB remote wakeup
usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.14-gentoo-r5-patch-vt1211 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.0: port 2 portsc 018a,00
hub 2-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0000
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.1: port 1 portsc 008a,00
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.1: port 2 portsc 008a,00
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 4-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.2: port 1 portsc 008a,00
hub 4-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.2: port 2 portsc 008a,00
hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0000
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12 08:13:09 2005 UTC).
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:11.5 to 64
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[004063500002d2af]
uhci_hcd 0000:00:10.0: suspend_rh (auto-stop)
ALSA device list:
  #0: VIA 8235 with VT1616i at 0xc400, irq 5
oprofile: using timer interrupt.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
ip_conntrack version 2.3 (7168 buckets, 57344 max) - 216 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.  http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
uhci_hcd 0000:00:10.1: suspend_rh (auto-stop)
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices: 
PCI0 USB0 USB1 USB2 USB3 USB4 USB5 USB6 LAN0 AC97 MC97 UAR1 
ACPI: (supports S0 S1 S4 S5)
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
uhci_hcd 0000:00:10.2: suspend_rh (auto-stop)
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 152k freed
ieee1394: raw1394: /dev/raw1394 device initialized
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA CLE266 chipset
agpgart: AGP aperture is 128M @ 0xd0000000
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 12 (level, low) -> IRQ 12
[drm] Initialized via 2.9.0 20060111 on minor 0: 
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 12 (level, low) -> IRQ 12
Yenta: CardBus bridge found at 0000:00:0a.0 [1106:aa01]
Yenta: ISA IRQ mask 0x0c08, PCI irq 12
Socket status: 30000006
ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7
Yenta: CardBus bridge found at 0000:00:0a.1 [1106:aa01]
Yenta: ISA IRQ mask 0x0c08, PCI irq 7
Socket status: 30000006
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
vt1211: Ignoring new-style parameters in presence of obsolete ones
hwmon-vid: Unknown VRM version of your x86 CPU
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ieee1394: Node added: ID:BUS[0-01:1023]  GUID[080046010443c2d1]
ieee1394: Node suspended: ID:BUS[0-01:1023]  GUID[080046010443c2d1]
nfsd: last server has exited
nfsd: unexporting all filesystems
portmap: server localhost not responding, timed out
RPC: failed to contact portmap (errno -5).
RPC: failed to contact portmap (errno -5).
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
vt1211: Ignoring new-style parameters in presence of obsolete ones
hwmon-vid: Unknown VRM version of your x86 CPU
ieee1394: Node changed: 0-01:1023 -> 0-00:1023
ieee1394: Node resumed: ID:BUS[0-00:1023]  GUID[080046010443c2d1]
ieee1394: Node changed: 0-00:1023 -> 0-01:1023
ieee1394: Node changed: 0-01:1023 -> 0-00:1023
ieee1394: Node suspended: ID:BUS[0-00:1023]  GUID[080046010443c2d1]